linky, да сейчас сделаю. Вот меня только всё время смущает, что при перезагрузке реса с модемом на борту появляется сообщение, что идёт подсоединение, потм соединение установлено, но естественно модем как мигал так и мигает, а только в сетевухе устанавливаются DNS. Поэтому хочу уточнить, когда говорится перегрузить рес, модем уже должен в нём быть или перезагружать без модеме, а модем втыкать после перезагрузки? И если втыкать после перезагрузки modemdial надо включать и выключать или не трогать?
Вот, что получилось из поста выше (модем втыкал после перезагрузки, modemdial не использовал)
* usb_modeswitch: handle USB devices with multiple modes * Version 1.2.4 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x12d1 DefaultProduct= 0x155b TargetVendor= 0x12d1 TargetProduct= 0x1506 TargetClass= not set TargetProductList=""
DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243000000000000000000000011060000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set
InquireDevice disabled Success check disabled System integration mode disabled
usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Found 002 usb_os_find_busses: Found 001 usb_os_find_busses: Skipping non bus directory devices usb_os_find_devices: Found 001 on 002 usb_os_find_devices: Found 002 on 001 usb_os_find_devices: Found 001 on 001 error obtaining child information: Inappropriate ioctl for device Looking for target devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID searching devices, found USB ID 1d6b:0002 No devices in target mode or class found Looking for default devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID found matching product ID adding device searching devices, found USB ID 1d6b:0002 Found device in default mode, class or configuration (1) Accessing device 002 on bus 001 ... Getting the current device configuration ... OK, got current device configuration (1) Using interface number 0 Using endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification) ------------------------- Manufacturer: Product: Mobile Connect Serial No.: not provided ------------------------- Looking for active driver ... OK, driver found ("usb-storage") OK, driver "usb-storage" detached Setting up communication with interface 0 Using endpoint 0x01 for message sending ... Trying to send message 1 to endpoint 0x01 ... OK, message successfully sent Resetting response endpoint 0x81 USB error: could not clear/halt ep 129: No such device Could not reset endpoint (probably harmless): -19 Resetting message endpoint 0x01 USB error: could not clear/halt ep 1: No such device Could not reset endpoint (probably harmless): -19 USB error: could not release intf 0: No such device Device is gone, skipping any further commands -> Run lsusb to note any changes. Bye.
[root@stlinux]#dmesg | tail -n40 <4>save exit: isCheckpointed 1 <4>smart_ioctl------------------------->set handle <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <6>usb 1-1: new high speed USB device using stm-ehci and address 2 <6>usb 1-1: configuration #1 chosen from 1 choice <4>[usb_probe_interface]drive name=usb-storage <6>scsi0 : SCSI emulation for USB Mass Storage devices <7>usb-storage: device found at 2 <7>usb-storage: waiting for device to settle before scanning <4>[usb_probe_interface]drive name=usb-storage <6>scsi1 : SCSI emulation for USB Mass Storage devices <7>usb-storage: device found at 2 <7>usb-storage: waiting for device to settle before scanning <5>scsi 0:0:0:0: CD-ROM Mass Storage 2.31 PQ: 0 ANSI: 2 <7>usb-storage: device scan complete <5>scsi 1:0:0:0: Direct-Access SD Storage 2.31 PQ: 0 ANSI: 2 <5>sd 1:0:0:0: [sda] Attached SCSI removable disk <7>usb-storage: device scan complete <6>usb 1-1: USB disconnect, address 2 <6>usb 1-1: new high speed USB device using stm-ehci and address 3 <6>usb 1-1: configuration #1 chosen from 1 choice <4>[usb_probe_interface]drive name=usbserial_generic <4>[usb_probe_interface]drive name=usbserial_generic <4>[usb_probe_interface]drive name=usbserial_generic <4>[usb_probe_interface]drive name=option <6>option 1-1:1.0: GSM modem (1-port) converter detected <6>usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 <4>[usb_probe_interface]drive name=option <6>option 1-1:1.1: GSM modem (1-port) converter detected <6>usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 <4>[usb_probe_interface]drive name=option <6>option 1-1:1.2: GSM modem (1-port) converter detected <6>usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 [root@stlinux]# [root@stlinux]#
Почемуто после отключения CD он вроде как есть. Как то ранеее работая с модемом он у меня перевёлся в режим модем и интерфейс. И вроде где то видел , что модем переводили только в 2G. И всётаки наверное все проблемы в новой системе команд и новом драйвере из-за нового процессора. В аттаче что то для Linux из CD модема.
ВСЁ ЗАРАБОТАЛО. Перевёл модем в только модем и интерфейс командой ATI^SETPORT="A1;1,2" По getportmode выдаёт type: wcdma: ,mdm:0,pcui1 а до этого было ещё устройство diag:2
Перевёл модем в сеть только 2G. Воткнул в рес. Плагин modemdial не трогал (выкл). В настройках сети вкл. 3G. После включения показал как 3G включена но без IP и DN там были 0 и модем продолжал мигать. И сеть по лан оказалась
выключена как бы только 3G включена.
Потом 3G выключил. Включил плагин modemdial и модем включился и включилась 3G, т.е. модем светился постоянно как в коннекте с оператором. Зашёл в настройки сети 3G и там всё заполнено и IP и DNS. В плагинах рестартанул MGCAM и Ш@ра заработала.
Попался MF180 от Билайна, прошитый прошивкой от МТСа. Был переведен в режим только модем. Прошивка 1.2.58, в стардантном меню ресивера, естественно, работать не стал. А вот с помощью плагина завелся с полпинка. Работает уже больше 24 часов, все ОК. Linky респект и уважуха !!!
linky Повторить коннект модема после перезагрузки реса по ранее описаной схеме не получилось, видимо первый раз повлияли какието ранее выданые команды в терминале из предыдущего поста .
Спойлер:
STMicroelectronics Base Distribution version 2.2 Linux/sh4 2.6.32.42_stm24_V4.1-SAT7111_7111-STSDK
stlinux login: root Password:
Welcome to STMicroelectronics Base Distribution.
BusyBox v1.18.2 (2011-07-13 20:52:52 CST) built-in shell (ash) Enter 'help' for a list of built-in commands.
* usb_modeswitch: handle USB devices with multiple modes * Version 1.2.4 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x12d1 DefaultProduct= 0x155b TargetVendor= 0x12d1 TargetProduct= 0x1506 TargetClass= not set TargetProductList=""
DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243000000000000000000000011060000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set
InquireDevice disabled Success check disabled System integration mode disabled
usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Found 002 usb_os_find_busses: Found 001 usb_os_find_busses: Skipping non bus directory devices usb_os_find_devices: Found 001 on 002 usb_os_find_devices: Found 002 on 001 usb_os_find_devices: Found 001 on 001 error obtaining child information: Inappropriate ioctl for device Looking for target devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID searching devices, found USB ID 1d6b:0002 No devices in target mode or class found Looking for default devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID found matching product ID adding device searching devices, found USB ID 1d6b:0002 Found device in default mode, class or configuration (1) Accessing device 002 on bus 001 ... Getting the current device configuration ... OK, got current device configuration (1) Using interface number 0 Using endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification) ------------------------- Manufacturer: Product: Mobile Connect Serial No.: not provided ------------------------- Looking for active driver ... OK, driver found ("usb-storage") OK, driver "usb-storage" detached Setting up communication with interface 0 Using endpoint 0x01 for message sending ... Trying to send message 1 to endpoint 0x01 ... USB error: error reaping URB: No such device Device seems to have vanished right after sending. Good. Device is gone, skipping any further commands -> Run lsusb to note any changes. Bye.
[root@stlinux]#echo "12d1 1506" > /sys/bus/usb-serial/drivers/option1/new_id [root@stlinux]#cat /proc/tty/driver/usbserial usbserinfo:1.0 driver:2.0 0: module:option name:"GSM modem (1-port)" vendor:12d1 product:1506 num_ports:1 port:1 path:usb-stm-ehci.0-1 1: module:option name:"GSM modem (1-port)" vendor:12d1 product:1506 num_ports:1 port:1 path:usb-stm-ehci.0-1 [root@stlinux]#dmesg | tail -n40 <4>IRQ 156/BLITTER: IRQF_DISABLED is not guaranteed on shared IRQs <6>input: ywvinput as /devices/virtual/input/input0 <6>input: droidinput as /devices/virtual/input/input1 <4>IRQ 156/STGFB_Blitter: IRQF_DISABLED is not guaranteed on shared IRQs <4>*********get viewport handle: 0xc17b4e4c, 0xc17b4e4c <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>*********get viewport handle: 0x0, 0x0 <4>*********get viewport handle: 0xc17b4e4c, 0xc17b4e4c <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>smart_ioctl------------------------->set handle <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <6>usb 1-1: new high speed USB device using stm-ehci and address 2 <6>usb 1-1: configuration #1 chosen from 1 choice <4>[usb_probe_interface]drive name=usb-storage <6>scsi0 : SCSI emulation for USB Mass Storage devices <7>usb-storage: device found at 2 <7>usb-storage: waiting for device to settle before scanning <5>scsi 0:0:0:0: CD-ROM Mass Storage 2.31 PQ: 0 ANSI: 2 <7>usb-storage: device scan complete <6>warning: `vsftpd' uses 32-bit capabilities (legacy support in use) <6>usb 1-1: USB disconnect, address 2 <6>usb 1-1: new high speed USB device using stm-ehci and address 3 <6>usb 1-1: configuration #1 chosen from 1 choice <4>[usb_probe_interface]drive name=usbserial_generic <4>[usb_probe_interface]drive name=usbserial_generic <4>[usb_probe_interface]drive name=option <6>option 1-1:1.0: GSM modem (1-port) converter detected <6>usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 <4>[usb_probe_interface]drive name=option <6>option 1-1:1.1: GSM modem (1-port) converter detected <6>usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 [root@stlinux]# [root@stlinux]#
После очередных попыток опять подрубился модем и работает.Но как то зависит его подключение от манипуляции с лановской сеткой и включением и выключением в настройках сети 3G. И видимо от команды в телнете /etc/ppp/usb_modeswitch -I -W -c /etc/ppp/switch/12d1:155b без неё подключения полюбому не происходит, а после неё потанцевав с бубном получается стартануть модемНа сегодня пока всё.
artems, Отлично!!! Значит нужно было его перевести самим !!! Сейчас подправлю скрипт и будет все автоматом 1 пост обновил. Установи как все описано по новой перегрузи рес. После полной загрузки подключи модем. Ничего не запускай из меню плагин. Выполни /etc/ppp/usb_modeswitch -W -c /etc/ppp/switch/12d1:155b потом dmesg | tail -n40 cat /proc/tty/driver/usbserial Если ответы будут как ранее с ttyUSB то выруби модем, подключи Из меню плагина нажми Modemdial покажи лог из /tmp/log или cat /tmp/log
Попался MF180 от Билайна, прошитый прошивкой от МТСа. Был переведен в режим только модем. Прошивка 1.2.58, в стардантном меню ресивера, естественно, работать не стал. А вот с помощью плагина завелся с полпинка. Работает уже больше 24 часов, все ОК. Linky респект и уважуха !!!
А попробуй не переведенный в режим модем, и покажи файл лога. Где и что написано в 1 посте.
artems, Отлично!!! Значит нужно было его перевести самим !!! Сейчас подправлю скрипт и будет все автоматом 1 пост обновил. Установи как все описано по новой перегрузи рес. После полной загрузки подключи модем. Ничего не запускай из меню плагин. Выполни /etc/ppp/usb_modeswitch -W -c /etc/ppp/switch/12d1:155b потом dmesg | tail -n40 cat /proc/tty/driver/usbserial Если ответы будут как ранее с ttyUSB то выруби модем, подключи Из меню плагина нажми Modemdial покажи лог из /tmp/log или cat /tmp/log
Сегодня никак не получается повторить вчерашний успех.
* usb_modeswitch: handle USB devices with multiple modes * Version 1.2.4 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x12d1 DefaultProduct= 0x155b TargetVendor= 0x12d1 TargetProduct= 0x1506 TargetClass= not set TargetProductList=""
DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243000000000000000000000011060000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set
InquireDevice enabled (default) Success check disabled System integration mode disabled
usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Found 002 usb_os_find_busses: Found 001 usb_os_find_busses: Skipping non bus directory devices usb_os_find_devices: Found 001 on 002 usb_os_find_devices: Found 002 on 001 usb_os_find_devices: Found 001 on 001 error obtaining child information: Inappropriate ioctl for device Looking for target devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID searching devices, found USB ID 1d6b:0002 No devices in target mode or class found Looking for default devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID found matching product ID adding device searching devices, found USB ID 1d6b:0002 Found device in default mode, class or configuration (1) Accessing device 002 on bus 001 ... Getting the current device configuration ... OK, got current device configuration (1) Using interface number 0 Using endpoints 0x01 (out) and 0x81 (in) Inquiring device details; driver will be detached ... Looking for active driver ... OK, driver found ("usb-storage") OK, driver "usb-storage" detached
SCSI inquiry data (for identification) ------------------------- Vendor String: Model String: Mass Storage Revision String: 2.31 -------------------------
USB description data (for identification) ------------------------- Manufacturer: Product: Mobile Connect Serial No.: not provided ------------------------- Setting up communication with interface 0 Using endpoint 0x01 for message sending ... Trying to send message 1 to endpoint 0x01 ... USB error: error reaping URB: No such device Device seems to have vanished right after sending. Good. Device is gone, skipping any further commands -> Run lsusb to note any changes. Bye.
[root@stlinux]#dmesg | tail -n40 <6>usbcore: registered new interface driver sierra <6>sierra: v.1.3.8:USB Driver for Sierra Wireless USB modems <4>IRQ 156/BLITTER: IRQF_DISABLED is not guaranteed on shared IRQs <6>input: ywvinput as /devices/virtual/input/input0 <6>input: droidinput as /devices/virtual/input/input1 <4>IRQ 156/STGFB_Blitter: IRQF_DISABLED is not guaranteed on shared IRQs <4>*********get viewport handle: 0xc17b4e4c, 0xc17b4e4c <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>*********get viewport handle: 0x0, 0x0 <4>*********get viewport handle: 0xc17b4e4c, 0xc17b4e4c <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>smart_ioctl------------------------->set handle <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <6>usb 1-1: new high speed USB device using stm-ehci and address 2 <6>usb 1-1: configuration #1 chosen from 1 choice <4>[usb_probe_interface]drive name=usb-storage <6>scsi0 : SCSI emulation for USB Mass Storage devices <7>usb-storage: device found at 2 <7>usb-storage: waiting for device to settle before scanning <5>scsi 0:0:0:0: CD-ROM Mass Storage 2.31 PQ: 0 ANSI: 2 <7>usb-storage: device scan complete <4>usb 1-1: usbfs: process 1344 (usb_modeswitch) did not claim interface 0 before use <6>usb 1-1: USB disconnect, address 2 <6>usb 1-1: new high speed USB device using stm-ehci and address 3 <6>usb 1-1: configuration #1 chosen from 1 choice <4>[usb_probe_interface]drive name=usbserial_generic <4>[usb_probe_interface]drive name=usbserial_generic [root@stlinux]#
PPPD is offline. Trying to start ... Trying to switch: Huawei switch to Modem mode Trying find port after switching to modem mode:...[ OK ] Trying find port:...[ OK ] Starting pppd: Failed to open /dev/ttyUSB0: No such device Failed to open /dev/ttyUSB0: No such device [FAILED]
artems, ключ не сработал InquireDevice enabled (default) на перегруженном ресе введи только /etc/ppp/usb_modeswitch -W -I -c /etc/ppp/switch/12d1:155b потом cat /proc/tty/driver/usbserial странно у себя проверил все работает, ты скрипт обновлял полностью через Untargz? все как в 1 посте написано?
* usb_modeswitch: handle USB devices with multiple modes * Version 1.2.4 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x12d1 DefaultProduct= 0x155b TargetVendor= 0x12d1 TargetProduct= 0x1506 TargetClass= not set TargetProductList=""
DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243000000000000000000000011060000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set
InquireDevice disabled Success check disabled System integration mode disabled
usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Found 002 usb_os_find_busses: Found 001 usb_os_find_busses: Skipping non bus directory devices usb_os_find_devices: Found 001 on 002 usb_os_find_devices: Found 002 on 001 usb_os_find_devices: Found 001 on 001 error obtaining child information: Inappropriate ioctl for device Looking for target devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID searching devices, found USB ID 1d6b:0002 No devices in target mode or class found Looking for default devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID found matching product ID adding device searching devices, found USB ID 1d6b:0002 Found device in default mode, class or configuration (1) Accessing device 002 on bus 001 ... Getting the current device configuration ... OK, got current device configuration (1) Using interface number 0 Using endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification) ------------------------- Manufacturer: Product: Mobile Connect Serial No.: not provided ------------------------- Looking for active driver ... OK, driver found ("usb-storage") OK, driver "usb-storage" detached Setting up communication with interface 0 Using endpoint 0x01 for message sending ... Trying to send message 1 to endpoint 0x01 ... USB error: error reaping URB: No such device Device seems to have vanished right after sending. Good. Device is gone, skipping any further commands -> Run lsusb to note any changes. Bye.
Сегодня файл 12d1:155b почему то по сравнению со вчерашним дополнился строчкой InquireDevice= 0 . Вот после обновления плагина modemdial сегодня никак не подключается. Я уже попробовал установить прошлый плагин и всё попробовать, но безрезультатно. В новой версии плагина может какие файлы ещё обновились и прошлым плагином не восстанавливаются?
artems, На перегруженом ресе покажи lsmod и cat /root/spark/modules/option.ko | grep 1506 Потом так echo "12d1 1506" > /sys/bus/usb-serial/drivers/option1/new_id и так /etc/ppp/usb_modeswitch -W -I -c /etc/ppp/switch/12d1:155b потом cat /proc/tty/driver/usbserial
Сейчас подключен ХАБ или ранее был? Только InquireDevice= 0 добавил
Потом так echo "12d1 1506" > /sys/bus/usb-serial/drivers/option1/new_id и так /etc/ppp/usb_modeswitch -W -I -c /etc/ppp/switch/12d1:155b потом cat /proc/tty/driver/usbserial
Сейчас подключен ХАБ или ранее был?
А дальше? и что с хабом? он ранее был? или сейчас есть?
Когда вчера прошло подключение и сегодня хаба не было.Вчера ещё раз подключал, но как то криво я уже писал. В настройках сети при подключении 3G происходит подключение, затем пишет соединение установлено и в сети 3G заполнеяется нулями DNS.Потм заходил в плагины , запускал modemdial и модем подрубался, в настройках 3G заполнялось провайдером МТС и работала Ш@ра. Сегодня никаким способом ничего не получается. Так в спойлере результат последнего поста т.е. не подключается. Сегодня тоже пишет идёт подключение, но в сети3G ничего не меняется, как было вчера.
Сейчас и вчера хаба нет. Сетка по верёвке , модем в USB. Такое впечатление, что подрубается как бы к сетевой карте с соответствующими выводами.
artems, То что подрубает что то в 3Г меню это гуи спарк пробует модем поднять, там жесткая привязка к хайвей. Попробуй драйвер заменить и рес перегрузить и повыполнять что выше написано
* usb_modeswitch: handle USB devices with multiple modes * Version 1.2.4 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x12d1 DefaultProduct= 0x155b TargetVendor= 0x12d1 TargetProduct= 0x1506 TargetClass= not set TargetProductList=""
DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243000000000000000000000011060000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set
InquireDevice disabled Success check disabled System integration mode disabled
usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Found 002 usb_os_find_busses: Found 001 usb_os_find_busses: Skipping non bus directory devices usb_os_find_devices: Found 001 on 002 usb_os_find_devices: Found 002 on 001 usb_os_find_devices: Found 001 on 001 error obtaining child information: Inappropriate ioctl for device Looking for target devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID searching devices, found USB ID 1d6b:0002 No devices in target mode or class found Looking for default devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID found matching product ID adding device searching devices, found USB ID 1d6b:0002 Found device in default mode, class or configuration (1) Accessing device 002 on bus 001 ... Getting the current device configuration ... OK, got current device configuration (1) Using interface number 0 Using endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification) ------------------------- Manufacturer: Product: Mobile Connect Serial No.: not provided ------------------------- Looking for active driver ... OK, driver found ("usb-storage") OK, driver "usb-storage" detached Setting up communication with interface 0 Using endpoint 0x01 for message sending ... Trying to send message 1 to endpoint 0x01 ... USB error: error reaping URB: No such device Device seems to have vanished right after sending. Good. Device is gone, skipping any further commands -> Run lsusb to note any changes. Bye.
* usb_modeswitch: handle USB devices with multiple modes * Version 1.2.4 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x12d1 DefaultProduct= 0x155b TargetVendor= 0x12d1 TargetProduct= 0x1506 TargetClass= not set TargetProductList=""
DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243000000000000000000000011060000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set
InquireDevice disabled Success check disabled System integration mode disabled
usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Found 002 usb_os_find_busses: Found 001 usb_os_find_busses: Skipping non bus directory devices usb_os_find_devices: Found 001 on 002 usb_os_find_devices: Found 006 on 001 usb_os_find_devices: Found 001 on 001 error obtaining child information: Inappropriate ioctl for device Looking for target devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID searching devices, found USB ID 1d6b:0002 No devices in target mode or class found Looking for default devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:155b found matching vendor ID found matching product ID adding device searching devices, found USB ID 1d6b:0002 Found device in default mode, class or configuration (1) Accessing device 006 on bus 001 ... Getting the current device configuration ... OK, got current device configuration (1) Using interface number 0 Using endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification) ------------------------- Manufacturer: Product: Mobile Connect Serial No.: not provided ------------------------- Looking for active driver ... OK, driver found ("usb-storage") OK, driver "usb-storage" detached Setting up communication with interface 0 Using endpoint 0x01 for message sending ... Trying to send message 1 to endpoint 0x01 ... OK, message successfully sent Resetting response endpoint 0x81 USB error: could not clear/halt ep 129: No such device Could not reset endpoint (probably harmless): -19 Resetting message endpoint 0x01 USB error: could not clear/halt ep 1: No such device Could not reset endpoint (probably harmless): -19 USB error: could not release intf 0: No such device Device is gone, skipping any further commands -> Run lsusb to note any changes. Bye.
* usb_modeswitch: handle USB devices with multiple modes * Version 1.2.4 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x12d1 DefaultProduct= 0x155b TargetVendor= 0x12d1 TargetProduct= 0x1506 TargetClass= not set TargetProductList=""
DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243000000000000000000000011060000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set
InquireDevice disabled Success check disabled System integration mode disabled
usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Found 002 usb_os_find_busses: Found 001 usb_os_find_busses: Skipping non bus directory devices usb_os_find_devices: Found 001 on 002 usb_os_find_devices: Found 007 on 001 skipped 4 class/vendor specific interface descriptors skipped 4 class/vendor specific interface descriptors usb_os_find_devices: Found 001 on 001 error obtaining child information: Inappropriate ioctl for device Looking for target devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:1506 found matching vendor ID found matching product ID adding device searching devices, found USB ID 1d6b:0002 Found devices in target mode or class (1) Looking for default devices ... searching devices, found USB ID 1d6b:0001 searching devices, found USB ID 12d1:1506 found matching vendor ID searching devices, found USB ID 1d6b:0002 No devices in default mode found. Nothing to do. Bye.
[root@stlinux]#cat /proc/tty/driver/usbserial usbserinfo:1.0 driver:2.0 [root@stlinux]#dmesg | tail -n40 <4>save exit: isCheckpointed 1 <6>usb 1-1: USB disconnect, address 3 <6>usb 1-1: new high speed USB device using stm-ehci and address 4 <6>usb 1-1: configuration #1 chosen from 1 choice <4>[usb_probe_interface]drive name=usb-storage <6>scsi1 : SCSI emulation for USB Mass Storage devices <7>usb-storage: device found at 4 <7>usb-storage: waiting for device to settle before scanning <5>scsi 1:0:0:0: CD-ROM Mass Storage 2.31 PQ: 0 ANSI: 2 <7>usb-storage: device scan complete <6>usb 1-1: USB disconnect, address 4 <6>usb 1-1: new high speed USB device using stm-ehci and address 5 <6>usb 1-1: configuration #1 chosen from 1 choice <4>[usb_probe_interface]drive name=usbserial_generic <4>[usb_probe_interface]drive name=usbserial_generic <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <6>usb 1-1: USB disconnect, address 5 <6>usb 1-1: new high speed USB device using stm-ehci and address 6 <6>usb 1-1: configuration #1 chosen from 1 choice <4>[usb_probe_interface]drive name=usb-storage <6>scsi2 : SCSI emulation for USB Mass Storage devices <7>usb-storage: device found at 6 <7>usb-storage: waiting for device to settle before scanning <5>scsi 2:0:0:0: CD-ROM Mass Storage 2.31 PQ: 0 ANSI: 2 <7>usb-storage: device scan complete <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <4>save exit: isCheckpointed 1 <6>warning: `vsftpd' uses 32-bit capabilities (legacy support in use) <6>usb 1-1: USB disconnect, address 6 <6>usb 1-1: new high speed USB device using stm-ehci and address 7 <6>usb 1-1: configuration #1 chosen from 1 choice <4>[usb_probe_interface]drive name=usbserial_generic <4>[usb_probe_interface]drive name=usbserial_generic [root@stlinux]#
artems, Очень странно, в драйвераз 1506 есть, но получается порты появляются только если ты вводишь echo "12d1 1506" > /sys/bus/usb-serial/drivers/option1/new_id а потом команды на переключения Попробуй эту команду потом echo "12d1 1506" > /sys/bus/usb-serial/drivers/option1/new_id и /etc/ppp/usb_modeswitch -W -c /etc/ppp/switch/12d1:155b и cat /proc/tty/driver/usbserial
Спойлер :
