# dmesg
<4>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<4>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
<4>free_all_bootmem_core: Free allocator bitmap
<6>Memory: 92036k/262144k available (2721k kernel code, 169856k reserved, 507k data, 152k init, 0k highmem)
<7>Calibrating delay loop... 295.93 BogoMIPS (lpj=147968)
<4>Mount-cache hash table entries: 512
<4>get_RSVD_size: Returning Size 0x0a000000
<4>Checking for 'wait' instruction...  available.
<6>NET: Registered protocol family 16
<6>usbcore: registered new driver hub
<4>     PCI DEV in slot 4, ID=1814:0301
PCI PnP: PCI_BAR[0] = ffff8000
<4>PCI PnP: size requested is 8000
<4>PnP: Writing PCI_MEM_BAR[0]=d1000000, size=32768, mask=ffff8000
<4>     PnP: PCI_DEV 1814:0301, command=4100146, msize=d1008000, iosize=00000000
<4>SATA: Primary Bus Master Status Register offset = b0520000 + 00000300 = b0520300
<4>SATA: before init Primary Bus Master Status reg = 0x00000000.
<4>SATA: after init Primary Bus Master Status reg = 0x00000020.
<6>squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
<6>JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
<6>Broadcom serial driver version 1.00 (2000-11-09) with SERIAL_PCI enabled
<6>Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
<4>ttyS0 at MMIO 0x0 (irq = 66) is a 16550A
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered
<6>loop: loaded (max 8 devices)
<4>Broadcom BCM740121 Ethernet Network Device v1.0 Jun 24 2010 15:10:39
<4>: Reading MAC address from BFFFFF94, FLASH_BASE=be000000
<4>: MAC address 00:08:DC:00:70:00 fetched from addr BFFFFF94
<4>: MAC Address: 00:08:DC:00:70:00
<4>SUNDRY revision = 74010021, have IP Hdr Opt=1
<4>init_buffers: 104 descriptors initialized
<4>init_buffers: 00000068 descriptors initialized, from flowctl
<6>BCMINTMAC: Auto-negotiation timed-out
<6>BCMINTMAC: 100 MB Full-Duplex (auto-neg)
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>Broadcom BCM7038 SATA IDE: IDE controller at PCI slot 0000:01:00.0
<6>Broadcom BCM7038 SATA IDE: chipset revision 0
<4>SUNDRY revision = 74010021
<4>Handling blacklisted models
<4>MDIO Read port0: 0000
<4>MDIO Read2 port0: 0004
<4>MDIO Read port1: 0000
<4>MDIO Read2 port1: 0004
<6>Broadcom BCM7038 SATA IDE: 100% native mode on irq 42
<6>    ide0: BM-DMA at 0x0300-0x0307, BIOS settings: hda:DMA, hdb:pio
<7>Probing IDE interface ide0...
<7>Probing IDE interface ide0...
<5>BCM97XXX flash device: 0x 2000000 at 0x1e000000
<6>Broadcom 9xxxx mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
<4> Amd/Fujitsu Extended Query Table at 0x0040
<5>fixup_use_write_buffers
<4>Broadcom 9xxxx mapped flash: CFI does not contain boot bank location. Assuming top.
<5>fixup_use_erase_chip
<5>number of CFI chips: 1
<5>cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
<5>Creating 8 MTD partitions on "Broadcom 9xxxx mapped flash":
<5>0x00000000-0x00300000 : "kernel"
<5>0x00300000-0x00700000 : "rootfs"
<5>0x00700000-0x01c00000 : "app"
<5>0x01c00000-0x01c80000 : "loader"
<5>0x01c80000-0x01fc0000 : "udata"
<5>0x01fc0000-0x01fe0000 : "splash"
<5>0x01fe0000-0x01ffff70 : "nvram"
<4>mtd: partition "nvram" doesn't end on an erase block -- force read-only
<5>0x01ffff70-0x02000000 : "macadr"
<4>mtd: partition "macadr" doesn't start on an erase block boundary -- force read-only
<5>usbmon: debugs is not available
<4>ehci_hcd_brcm_init: Initializing 1 EHCI devices
<4>10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
<4>drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
<4> - USB h/w setup mode <B>
<4> - USB power enable set for active HIGH mode
<4> - Resetting at b0480310
<4><-- brcm_ehci_hw_init
<6>brcm-ehci brcm-ehci.0: BRCM EHCI
<6>brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
<6>brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
<6>brcm-ehci brcm-ehci.0: park 0
<6>brcm-ehci brcm-ehci.0: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<4>2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
<4>drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
<4> - Resetting at b0480408
<4><-- brcm_start_hc
<6>brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
<6>brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 2
<6>brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 2 ports detected
<6>pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
<6>usb 1-1: new high speed USB device using brcm-ehci and address 2
<6>usbcore: registered new driver pegasus
<6>drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
<6>usbcore: registered new driver rtl8150
<6>usbcore: registered new driver asix
<6>NET: Registered protocol family 2
<6>IP: routing cache hash table of 2048 buckets, 16Kbytes
<4>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
<4>TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
<6>TCP: Hash tables configured (established 16384 bind 16384)
<6>NET: Registered protocol family 1
<6>NET: Registered protocol family 17
<4>Empty flash at 0x0000fffc ends at 0x00010000
<5>Eraseblock header found at 0x00010000 is not at the beginning of block (0x00000000)
<4>Empty flash at 0x0002ff9c ends at 0x00030000
<5>Eraseblock header found at 0x00030000 is not at the beginning of block (0x00020000)
<4>Empty flash at 0x0004fffc ends at 0x00050000
<5>Eraseblock header found at 0x00050000 is not at the beginning of block (0x00040000)
<4>Empty flash at 0x0006fffc ends at 0x00070000
<5>Eraseblock header found at 0x00070000 is not at the beginning of block (0x00060000)
<4>Empty flash at 0x0008fffc ends at 0x00090000
<5>Eraseblock header found at 0x00090000 is not at the beginning of block (0x00080000)
<4>Empty flash at 0x000afffc ends at 0x000b0000
<5>Eraseblock header found at 0x000b0000 is not at the beginning of block (0x000a0000)
<4>Empty flash at 0x000cfffc ends at 0x000d0000
<5>Eraseblock header found at 0x000d0000 is not at the beginning of block (0x000c0000)
<4>Empty flash at 0x000efffc ends at 0x000f0000
<5>Eraseblock header found at 0x000f0000 is not at the beginning of block (0x000e0000)
<4>Empty flash at 0x0010fffc ends at 0x00110000
<5>Eraseblock header found at 0x00110000 is not at the beginning of block (0x00100000)
<4>Empty flash at 0x0012ffdc ends at 0x00130000
<5>Eraseblock header found at 0x00130000 is not at the beginning of block (0x00120000)
<4>Empty flash at 0x0014fffc ends at 0x00150000
<5>Eraseblock header found at 0x00150000 is not at the beginning of block (0x00140000)
<4>Empty flash at 0x0016fffc ends at 0x00170000
<5>Eraseblock header found at 0x00170000 is not at the beginning of block (0x00160000)
<4>Empty flash at 0x0018fffc ends at 0x00190000
<5>Eraseblock header found at 0x00190000 is not at the beginning of block (0x00180000)
<4>Empty flash at 0x001afffc ends at 0x001b0000
<5>Eraseblock header found at 0x001b0000 is not at the beginning of block (0x001a0000)
<4>Empty flash at 0x001cffcc ends at 0x001d0000
<5>Eraseblock header found at 0x001d0000 is not at the beginning of block (0x001c0000)
<4>Empty flash at 0x001efffc ends at 0x001f0000
<5>Eraseblock header found at 0x001f0000 is not at the beginning of block (0x001e0000)
<4>Empty flash at 0x0020ff74 ends at 0x00210000
<5>Eraseblock header found at 0x00210000 is not at the beginning of block (0x00200000)
<4>Empty flash at 0x0022fffc ends at 0x00230000
<5>Eraseblock header found at 0x00230000 is not at the beginning of block (0x00220000)
<4>Empty flash at 0x0024fffc ends at 0x00250000
<5>Eraseblock header found at 0x00250000 is not at the beginning of block (0x00240000)
<4>Empty flash at 0x0026fffc ends at 0x00270000
<5>Eraseblock header found at 0x00270000 is not at the beginning of block (0x00260000)
<4>Empty flash at 0x0028ff70 ends at 0x00290000
<5>Eraseblock header found at 0x00290000 is not at the beginning of block (0x00280000)
<4>Empty flash at 0x002afffc ends at 0x002b0000
<5>Eraseblock header found at 0x002b0000 is not at the beginning of block (0x002a0000)
<4>Empty flash at 0x002cfffc ends at 0x002d0000
<5>Eraseblock header found at 0x002d0000 is not at the beginning of block (0x002c0000)
<4>Empty flash at 0x002efffc ends at 0x002f0000
<5>Eraseblock header found at 0x002f0000 is not at the beginning of block (0x002e0000)
<4>Empty flash at 0x0030fffc ends at 0x00310000
<5>Eraseblock header found at 0x00310000 is not at the beginning of block (0x00300000)
<4>VFS: Mounted root (jffs2 filesystem) readonly.
<4>free_initmem: init_begin=80329000, init_end=8034f000
<6>Freeing unused kernel memory: 152k freed
<4>Warning: unable to open an initial console.
<4>Algorithmics/MIPS FPU Emulator v1.5
<5>SCSI subsystem initialized
<6>Initializing USB Mass Storage driver...
<6>scsi0 : SCSI emulation for USB Mass Storage devices
<7>usb-storage: device found at 2
<7>usb-storage: waiting for device to settle before scanning
<6>usbcore: registered new driver usb-storage
<6>USB Mass Storage support registered.
<5>  Vendor: SAMSUNG   Model: HM321HI           Rev:
<5>  Type:   Direct-Access                      ANSI SCSI revision: 02
<5>SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
<3>sda: assuming drive cache: write through
<5>SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
<3>sda: assuming drive cache: write through
<6> sda:<4>bcmdriver: module license 'Proprietary' taints kernel.
<4>Initializing bcmdriver version $ 27 $
<4>MCK - Using Interrupt Definition for 7401c0 (uname -a)
<4>chipConfigs[4].maxNumIrq = 65
<4>Global Interrupt Mask Low: 0xD15F7FFF, High: 0x1C0C11D3
<4>Initialization complete...
<4> sda1
<5>Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
<7>usb-storage: device scan complete
<4>get_RSVD_size: Returning Size 0x0a000000
<4>RT61: Vendor = 0x1814, Product = 0x0301
<7>PCI: Setting latency timer of device 0000:00:04.0 to 64
<6>usbcore: registered new driver rt73
<2>eth0 Link UP.
<4>rtusb init --->
<6>usbcore: registered new driver rt2870
<4>RT61: RfIcType= 3
<4>32:33:31:37:31:00:00:00:00:00:00:00:00:00:00:00:
<6>kjournald starting.  Commit interval 5 seconds
<4>EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
<6>EXT3 FS on sda1, internal journal
<6>EXT3-fs: recovery complete.
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>Adding 15992k swap on /mnt/USB1/sda1/swap/swapfile.  Priority:-1 extents:5
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
<2>eth0 Link DOWN.
<2>eth0 Link UP.
#