=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.12.14 01:25:35 =~=~=~=~=~=~=~=~=~=~=~=
яCPU 01
BCM74390012
PRID07251112
v1.7
RR:00000003
BFW
SEC
seclib-1.5
BBL v1.0.1
AVS init...
spare0/rmon_hz=01797476
spare1/rmon_vt=01797476
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
AVS load_code offset =00051000
AVS: OTP Decrypt 0x00000000, OTP Verify AVS 0x00000000
LOADED
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MemsysFW: OTP Decrypt 0x00000000, OTP Secure Boot 0x00000000
SHMOO 01020000 BLD:9695 HW:hpf0_b1p6 V:1.2.0.0
MCB: FIX
AVS start:status=000000ff
STB: Current voltage=000003c2(962)
temperature=0000c5ca(50634)
PV=00000372(882)
MV=000003c2(962)
AVS FW rev=30333078 [0.3.0.x]
OK
DDR0: *@ ffe0ba98 <= ffe0ba98 MEMSYS-0 @ f1100000 OK
DDR1: -
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
OTP SSBL Encrypt 0x00000000
OTP Sec Boot 0x00000000
OTP read MichEn 0x00000000
MICH: disable success
SSBL
no v092_to_v095 conversion is performed
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 0704cf70
_ebss 0704ea38
_end 0704ea58
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 0704cf70 to 0704ea38 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
GO!
[33;1m ,/ [0m
[33;1m ,'/___,[0m BOLT v1.07 v1.07-r19 LOCAL BUILD
[33;1m.'__ ,' [0m (2016-09-21 )
[33;1m /,' [0m Copyright (C) 2016 Broadcom Corporation
[33;1m /' [0m
[0m
Board: BCM97251SSV
SYS_CTRL: product=72511, family=7439b2, strap=000000b2,
otp @ 0xf0404030 = 0x822080e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) memsys_1_disable(0x00008000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000461: moca2_disable(0x00000001) pcie1_disable(0x00000040) rfm_disable(0x00000020) sata1_disable(0x00000400)
CPU: 2x A15, 1719 MHz
SCB: 432 MHz
DDR0 @ 1061MHz, DDR1 N/A
CS0: SFDP SPI, 8MB, 64kB blocks, 256B pages
[31;1mCS1: NAND: unrecognized ID: 0xffffffff 0xffffffff[0m
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 1
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.961V, T=+50.634C, PV=0.882V, MV=0.962V, FW=30333078 [0.3.0.x]
USB otp=00000040
[36;1mboard selection update![0m
[36;1mboard was ?, now a (flags:0xffe00000)[0m
USB @ 0xf0470200: IPP is active low, IOC is negative polarity
usb: resetting device on bus 0 hub 1 port 1[J
USB: New high speed device connected to bus 0 hub 1 port 1[J
usb: resetting device on bus 0 hub 2 port 1[J
USB: New full speed device connected to bus 0 hub 2 port 1[J
USB: Lower speed devices not supported under high speed hub[J
usb: resetting device on bus 0 hub 2 port 2[J
USB: New high speed device connected to bus 0 hub 2 port 2[J
usb: found Mass-Storage Device 13fe:1d00
USBMASS: Unit 0 connected[J
flashing
Reading usbdisk0:hd51/disk.img: ...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
...........
16777216 bytes read
16777216 bytes written
........
12582912 bytes read
12582912 bytes written
0 bytes read
Done. 314572800 bytes written
Erasing flash...
Done. 3909091328 bytes
completed!
reboot
CPU 01
BCM74390012
PRID07251112
v1.7
RR:00000200
BFW
SEC
seclib-1.5
BBL v1.0.1
AVS init...
spare0/rmon_hz=01797475
spare1/rmon_vt=01797476
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a252b25
AVS load_code offset =00051000
AVS: OTP Decrypt 0x00000000, OTP Verify AVS 0x00000000
LOADED
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2525
MemsysFW: OTP Decrypt 0x00000000, OTP Secure Boot 0x00000000
SHMOO 01020000 BLD:9695 HW:hpf0_b1p6 V:1.2.0.0
MCB: FIX
AVS start:status=000000ff
STB: Current voltage=000003cb(971)
temperature=0000cb7f(52095)
PV=00000379(889)
MV=000003cb(971)
AVS FW rev=30333078 [0.3.0.x]
OK
DDR0: *@ ffe0ba98 <= ffe0ba98 MEMSYS-0 @ f1100000 OK
DDR1: -
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
OTP SSBL Encrypt 0x00000000
OTP Sec Boot 0x00000000
OTP read MichEn 0x00000000
MICH: disable success
SSBL
no v092_to_v095 conversion is performed
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 0704cf70
_ebss 0704ea38
_end 0704ea58
HEAP @ 07100000
STACK @ 09200000
ARCH: CONFIG OK
CLR BSS 0704cf70 to 0704ea38 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
GO!
[33;1m ,/ [0m
[33;1m ,'/___,[0m BOLT v1.07 v1.07-r19 LOCAL BUILD
[33;1m.'__ ,' [0m (2016-09-21 )
[33;1m /,' [0m Copyright (C) 2016 Broadcom Corporation
[33;1m /' [0m
[0m
Board: BCM97251SSV
SYS_CTRL: product=72511, family=7439b2, strap=000000b2,
otp @ 0xf0404030 = 0x822080e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) memsys_1_disable(0x00008000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000461: moca2_disable(0x00000001) pcie1_disable(0x00000040) rfm_disable(0x00000020) sata1_disable(0x00000400)
CPU: 2x A15, 1719 MHz
SCB: 432 MHz
DDR0 @ 1061MHz, DDR1 N/A
CS0: SFDP SPI, 8MB, 64kB blocks, 256B pages
[31;1mCS1: NAND: unrecognized ID: 0xffffffff 0xffffffff[0m
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 1
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.962V, T=+53.69C, PV=0.889V, MV=0.971V, FW=30333078 [0.3.0.x]
USB otp=00000040
[36;1mboard selection update![0m
[36;1mboard was ?, now a (flags:0xffe00000)[0m
Executing STARTUP...
Loader:zimg Filesys:raw Dev:emmcflash0.kernel1 File:(null) Options:root=/dev/mmcblk0p3 rw rootwait hd51_4.boxmode=1
Reading 4744168 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x761c000)
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.10.12 (nikolasi@nikolasi-M61PME-S2P) (gcc version 6.2.0 (GCC) ) #1 SMP Mon Dec 11 20:18:10 EET 2017
[ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt:Machine model: BCM97251SSV
[ 0.000000] cma: Reserved 440 MiB at 0x0000000014800000
[ 0.000000] cma: Reserved 192 MiB at 0x0000000030000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 14 pages/cpu @d3ddd000 s26764 r8192 d22388 u57344
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260416
[ 0.000000] Kernel command line: root=/dev/mmcblk0p3 rw rootwait hd51_4.boxmode=1 brcm_cma=440M@328M brcm_cma=192M@768M console=ttyS0,115200
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 380592K/1048576K available (6629K kernel code, 361K rwdata, 1832K rodata, 344K init, 223K bss, 20816K reserved, 647168K cma-reserved, 65536K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0681b08 (6631 kB)
[ 0.000000] .init : 0xc087a000 - 0xc08d0000 ( 344 kB)
[ 0.000000] .data : 0xc08d0000 - 0xc092a578 ( 362 kB)
[ 0.000000] .bss : 0xc092c000 - 0xc0963cb4 ( 224 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xf0805000, parent irq: 16)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xf0807000, parent irq: 17)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xf0809640, parent irq: 18)
[ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xf080b200, parent irq: 19)
[ 0.000000] irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xfc40a700, parent IRQ(s): 2)
[ 0.000000] irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xf080d380, parent IRQ(s): 3)
[ 0.000000] brcmstb: biuctrl: MCP: Write pairing already disabled
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 27.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x63a1e71a3, max_idle_ns: 440795203123 ns
[ 0.000003] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 4398046511093ns
[ 0.000012] Switching to timer-based delay loop, resolution 37ns
[ 0.000293] Console: colour dummy device 80x30
[ 0.000313] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
[ 0.000322] pid_max: default: 32768 minimum: 301
[ 0.000431] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000437] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000896] CPU: Testing write buffer coherency: ok
[ 0.001153] CPU0: update cpu_capacity 1024
[ 0.001159] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001372] Setting up static identity map for 0x8440 - 0x8498
[ 0.003448] smp: Bringing up secondary CPUs ...
[ 0.004179] CPU1: update cpu_capacity 1024
[ 0.004182] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.004244] smp: Brought up 1 node, 2 CPUs
[ 0.004254] SMP: Total of 2 processors activated (108.00 BogoMIPS).
[ 0.004259] CPU: All CPU(s) started in SVC mode.
[ 0.004656] devtmpfs: initialized
[ 0.010872] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[ 0.011065] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.011083] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.025437] NET: Registered protocol family 16
[ 0.025840] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.030398] cpuidle: using governor ladder
[ 0.033437] cpuidle: using governor menu
[ 0.042569] No ATAGs?
[ 0.042665] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.042674] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.057412] SCSI subsystem initialized
[ 0.057969] usbcore: registered new interface driver usbfs
[ 0.058019] usbcore: registered new interface driver hub
[ 0.058067] usbcore: registered new device driver usb
[ 0.058132] Linux cec interface: v0.10
[ 0.058183] Linux video capture interface: v2.00
[ 0.058252] pps_core: LinuxPPS API ver. 1 registered
[ 0.058257] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <
giometti@linux.it>
[ 0.058277] PTP clock support registered
[ 0.058807] Advanced Linux Sound Architecture Driver Initialized.
[ 0.060109] clocksource: Switched to clocksource arch_sys_counter
[ 0.060344] FS-Cache: Loaded
[ 0.066315] NET: Registered protocol family 2
[ 0.066757] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.066798] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.066873] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.066962] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.066990] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.067151] NET: Registered protocol family 1
[ 0.067532] RPC: Registered named UNIX socket transport module.
[ 0.067538] RPC: Registered udp transport module.
[ 0.067542] RPC: Registered tcp transport module.
[ 0.067545] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.067917] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[ 0.069294] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.069910] NFS: Registering the id_resolver key type
[ 0.069930] Key type id_resolver registered
[ 0.069934] Key type id_legacy registered
[ 0.069945] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.070199] fuse init (API version 7.26)
[ 0.072099] bounce: pool size: 64 pages
[ 0.072141] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.072151] io scheduler noop registered
[ 0.072158] io scheduler deadline registered
[ 0.072190] io scheduler cfq registered (default)
[ 0.072505] brcm-gisb-arb f0400000.gisb-arb: registered mem: f0a09000, irqs: 47, 48
[ 0.072815] brcm-sata-phy f0458100.sata-phy: registered 1 port(s)
[ 0.073177] brcm-cma brcm-cma.0: Initialized Broadcom CMA root device
[ 0.073891] brcm-cma brcm-cma.0: Added CMA device @ PA=0x14800000 LEN=0x1b800000
[ 0.074388] brcm-cma brcm-cma.1: Added CMA device @ PA=0x30000000 LEN=0xc000000
[ 0.108711] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.110248] console [ttyS0] disabled
[ 0.110289] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 34, base_baud = 5062500) is a 16550A
[ 0.786600] console [ttyS0] enabled
[ 0.790654] f040a940.serial: ttyS1 at MMIO 0xf040a940 (irq = 35, base_baud = 5062500) is a 16550A
[ 0.799971] f040a980.serial: ttyS2 at MMIO 0xf040a980 (irq = 36, base_baud = 5062500) is a 16550A
[ 0.816248] brd: module loaded
[ 0.823104] loop: module loaded
[ 0.827080] OF: /rdb/sata@f045a000/sata-port@0: could not get #phy-cells for /rdb/sata-phy@f0458100
[ 0.836249] brcm-ahci f045a000.sata: masking port_map 0x3 -> 0x1
[ 0.842322] brcm-ahci f045a000.sata: SSS flag set, parallel bus scan disabled
[ 0.859555] brcm-ahci f045a000.sata: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x1 impl platform mode
[ 0.868535] brcm-ahci f045a000.sata: flags: 64bit ncq sntf stag pm clo pmp slum part
[ 0.877675] scsi host0: brcm-ahci
[ 0.881271] scsi host1: brcm-ahci
[ 0.884756] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 44
[ 0.892683] ata2: DUMMY
[ 0.895143] brcm-ahci f045a000.sata: Broadcom AHCI SATA3 registered
[ 0.902079] libphy: Fixed MDIO Bus: probed
[ 0.906499] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
[ 0.924440] libphy: bcmgenet MII bus: probed
[ 0.951448] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 0.957299] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 0.983238] ehci-brcm: EHCI BRCM driver
[ 0.987206] ehci-brcm f0470300.ehci: EHCI Host Controller
[ 0.992639] ehci-brcm f0470300.ehci: new USB bus registered, assigned bus number 1
[ 1.010341] ehci-brcm f0470300.ehci: irq 147, io mem 0xf0470300
[ 1.022445] ehci-brcm f0470300.ehci: USB 2.0 started, EHCI 1.00
[ 1.028921] hub 1-0:1.0: USB hub found
[ 1.032710] hub 1-0:1.0: 1 port detected
[ 1.036918] ehci-brcm f0470500.ehci: EHCI Host Controller
[ 1.042350] ehci-brcm f0470500.ehci: new USB bus registered, assigned bus number 2
[ 1.060040] ehci-brcm f0470500.ehci: irq 148, io mem 0xf0470500
[ 1.072443] ehci-brcm f0470500.ehci: USB 2.0 started, EHCI 1.00
[ 1.078820] hub 2-0:1.0: USB hub found
[ 1.082604] hub 2-0:1.0: 1 port detected
[ 1.086731] ohci-brcm: OHCI BRCM driver
[ 1.090730] ohci-brcm f0470400.ohci: BRCM OHCI controller
[ 1.096157] ohci-brcm f0470400.ohci: new USB bus registered, assigned bus number 3
[ 1.103804] ohci-brcm f0470400.ohci: irq 149, io mem 0xf0470400
[ 1.165844] hub 3-0:1.0: USB hub found
[ 1.169629] hub 3-0:1.0: 1 port detected
[ 1.173785] ohci-brcm f0470600.ohci: BRCM OHCI controller
[ 1.179213] ohci-brcm f0470600.ohci: new USB bus registered, assigned bus number 4
[ 1.179449] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.193062] ohci-brcm f0470600.ohci: irq 150, io mem 0xf0470600
[ 1.207360] ata1.00: ATA-10: ST1000LM048-2E7172, SDM1, max UDMA/133
[ 1.213651] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.254843] hub 4-0:1.0: USB hub found
[ 1.258626] hub 4-0:1.0: 1 port detected
[ 1.260617] ata1.00: configured for UDMA/133
[ 1.260972] scsi 0:0:0:0: Direct-Access ATA ST1000LM048-2E71 SDM1 PQ: 0 ANSI: 5
[ 1.275198] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.281768] ehci-pci: EHCI PCI platform driver
[ 1.286287] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.292493] ohci-pci: OHCI PCI platform driver
[ 1.297345] xhci-hcd f0471000.xhci: xHCI Host Controller
[ 1.302692] xhci-hcd f0471000.xhci: new USB bus registered, assigned bus number 5
[ 1.310404] xhci-hcd f0471000.xhci: hcc params 0x0250f17d hci version 0x100 quirks 0x00010010
[ 1.318975] xhci-hcd f0471000.xhci: irq 151, io mem 0xf0471000
[ 1.325589] hub 5-0:1.0: USB hub found
[ 1.329380] hub 5-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 1.336651] xhci-hcd f0471000.xhci: xHCI Host Controller
[ 1.338129] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 1.338133] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.338166] sd 0:0:0:0: [sda] Write Protect is off
[ 1.338222] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.342583] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.365771] sda: sda1
[ 1.366560] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.381102] xhci-hcd f0471000.xhci: new USB bus registered, assigned bus number 6
[ 1.388639] usb 1-1: new high-speed USB device number 2 using ehci-brcm
[ 1.395381] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.404033] hub 6-0:1.0: USB hub found
[ 1.407829] hub 6-0:1.0: 2 ports detected
[ 1.412193] usbcore: registered new interface driver uas
[ 1.417604] usbcore: registered new interface driver usb-storage
[ 1.423820] mousedev: PS/2 mouse device common for all mice
[ 1.429721] i2c /dev entries driver
[ 1.433625] IR NEC protocol handler initialized
[ 1.438180] IR RC5(x/sz) protocol handler initialized
[ 1.443259] IR RC6 protocol handler initialized
[ 1.447804] IR JVC protocol handler initialized
[ 1.452345] IR Sony protocol handler initialized
[ 1.456977] IR SANYO protocol handler initialized
[ 1.461699] IR Sharp protocol handler initialized
[ 1.466426] IR MCE Keyboard/mouse protocol handler initialized
[ 1.472270] IR XMP protocol handler initialized
[ 1.476814] smssdio: Siano SMS1xxx SDIO driver
[ 1.481269] smssdio: Copyright Pierre Ossman
[ 1.485953] sdhci: Secure Digital Host Controller Interface driver
[ 1.492150] sdhci: Copyright(c) Pierre Ossman
[ 1.496520] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.504708] hub 1-1:1.0: USB hub found
[ 1.508571] hub 1-1:1.0: 4 ports detected
[ 1.539446] mmc0: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
[ 1.547034] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.552645] usbcore: registered new interface driver usbhid
[ 1.558235] usbhid: USB HID core driver
[ 1.564693] NET: Registered protocol family 17
[ 1.569212] Key type dns_resolver registered
[ 1.573590] ThumbEE CPU extension supported.
[ 1.577875] Registering SWP/SWPB emulation handler
[ 1.590531] ALSA device list:
[ 1.593523] No soundcards found.
[ 1.597557] Waiting for root device /dev/mmcblk0p3...
[ 1.673831] mmc0: new high speed MMC card at address 0001
[ 1.679648] mmcblk0: mmc0:0001 4FPD3R 3.64 GiB
[ 1.684320] mmcblk0boot0: mmc0:0001 4FPD3R partition 1 4.00 MiB
[ 1.690393] mmcblk0boot1: mmc0:0001 4FPD3R partition 2 4.00 MiB
[ 1.696461] mmcblk0rpmb: mmc0:0001 4FPD3R partition 3 512 KiB
[ 1.704376] Alternate GPT is invalid, using primary GPT.
[ 1.709733] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9
[ 1.718107] EXT4-fs (mmcblk0p3): couldn't mount as ext3 due to feature incompatibilities
[ 1.734163] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 1.742312] VFS: Mounted root (ext4 filesystem) on device 179:3.
[ 1.749208] devtmpfs: mounted
[ 1.752584] Freeing unused kernel memory: 344K
[ 1.757041] This architecture does not have kernel memory protection.
INIT: version 2.88 booting
[ 1.815451] usb 1-1.1: new full-speed USB device number 3 using ehci-brcm
[ 1.843594] random: fast init done
[ 1.920469] usb 1-1.2: new high-speed USB device number 4 using ehci-brcm
[ 1.945726] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 1.962122] scsi host2: usb-storage 1-1.2:1.0
rmdir: '/media/hdd': No such file or directory
[ 2.660627] EXT4-fs (sda1): recovery complete
[ 2.688230] EXT4-fs (sda1): mounted filesystem with writeback data mode. Opts: (null)
[ 2.800585] hd51_1: loading out-of-tree module taints kernel.
[ 2.807581] usbcore: registered new interface driver tpm
[ 2.978524] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 2.987782] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.994126] sd 2:0:0:0: [sdb] 8060928 512-byte logical blocks: (4.13 GB/3.84 GiB)
[ 3.002572] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.008368] sd 2:0:0:0: [sdb] No Caching mode page found
[ 3.013735] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 3.027529] sdb: sdb1
[ 3.033705] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 3.384716] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4.853060] hd51: module_layout: kernel tainted.
[ 4.857729] Disabling lock debugging due to kernel taint
[ 5.131201] hd51: Unknown symbol pm_power_off_prepare (err 0)
[ 5.158937] EXT4-fs (mmcblk0p3): re-mounted. Opts: data=ordered
/dev/dvb/adapter0/video0: No such file or directory
ALSA: Restoring mixer settings...
/usr/sbin/alsactl: load_state:1735: No soundcards found...
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.dirty_rati
INIT: Entering runlevel: 3
Configuring network interfaces... [ 6.180441] f0b00000.etherne:01: Broadcom BCM7439 (2) PHY revision: 0x10, patch: 1
[ 6.189714] bcmgenet f0b00000.ethernet: configuring instance for internal PHY
udhcpc: option -h NAME is deprecated, use -x hostname:NAME
udhcpc (v1.24.1) started
Sending discover...
Sending discover...
[ 9.478481] bcmgenet f0b00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Sending discover...
Sending select for 192.168.100.10...
Lease of 192.168.100.10 obtained, lease time 86400
/etc/udhcpc.d/50default: Adding DNS 192.168.100.1
done.
Starting system message bus: dbus.
bootvideo found @ /usr/share/bootvideo.mp4
grep: /etc/enigma2/settings: No such file or directory
{"EPLAYER3_EXTENDED":{"version":36}}
file: [file:///usr/share/bootvideo.mp4]
{"PLAYBACK_OPEN":{"OutputName":"Output", "file":"file:///usr/share/bootvideo.mp4", "sts":0}}
{"OUTPUT_OPEN":{"sts":-1}}
{"PLAYBACK_PLAY":{"sts":0}}
{"v_c":{"id":1,"e":"V_MPEG4","n":"und","w":1280,"h":720,"f":29960,"p":-1,"an":1,"ad":1}}
{"a_l": [{"id":2,"e":"A_AAC","n":"eng"}]}
{"a_c":{"id":2,"e":"A_AAC","n":"eng"}}
{"s_l": []}
{"s_c":{"id":-1,"e":"","n":""}}
{"log":"Frame read error: 'End of file'"}
Starting Dropbear SSH server: Generating key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQCP8nR19k/8zNXEGHt4wDC8ru+bm2nQs5Iy7pXUvziHPngXmakY+MF3fZN8TvhHhkUY8YqjrFvazaxcjhKWebztPZ9UjzgigD3W2CJeo4khO12tp5wn+LvKPakMPWzHY5t8YEz+VceCRYXUShoOkd1mnAaUCIFty2hjYwxp6r3TWw== root@hd51
Fingerprint: md5 5a:ed:bf:13:a6:8c:0f:84:89:0a:dd:e8:bd:e7:3c:a2
[ 14.747684] NET: Registered protocol family 10
[ 14.753920] Segment Routing with IPv6
dropbear.
Starting rpcbind daemon...done.
Mounting remote filesystems...
starting statd: done
starting Busybox Periodic Command Scheduler: crond... done.
crond[2068]: crond (busybox 1.24.1) started, log level 8
Fuse filesystem already available.
Mounting fuse control filesystem.
Starting internet superserver: inetd.
Starting Samba: smbd[ 15.183055] random: crng init done
nmbd.
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
...done.
Running ciplushelper...done.
Mount is denied because the NTFS volume is already exclusively opened.
The volume may be already mounted, or another software may use it which
could be identified for example by the help of the 'fuser' command.
mount: mounting /dev/sda1 on /hdd failed: Device or resource busy
swap: missing /var/etc/settings.swap
Starting transmission-daemon
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
DVB_API_VERSION 5 DVB_API_VERSION_MINOR 10
ENIGMA_DEBUG_LVL=3
[gFBDC] no framebuffer available
Segmentation fault
INIT: Id "gui" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
Мобильная версия | Карта сайта | Отказ от ответственности | Реклама
